Видео

Thank you.

No thing beats Honda.

I always just add an inner tube. Easy and lasts a really long time.

JD has been doing this longer than Briggs. Proof? Plastic hoods. My $1000 MTD has a stamped steel hood. Solid as can be. The $6000 JD has a plastic hood that is so flimsy you have to use caution when you open it. Then they put some catches on it so you have to yank it to get it open. Obviously money or cost savings isnt the issue. The MTD uses metal that will outlive the machine. Selling expensive parts down the road is the plan. To replace the whole hood assembly, an aftermarket one is around $5-600. Imagine JDs price.

Thanks for the great tutorial. Fixed my gx345 carb leak from overflow. Very helpfull👍🏼👍🏼

One very important question is do you know JESUS CHRIST AS YOUR PERSONAL LORD AND SAVIOR?

💯🏆

Put black rtv at the warped manifold will probably fix surging

Ground was my issue too on a Cub Cadet RZT SX... Thanks for the tips

The tension pulley bracket is bent. The pulley should be level with the other pulleys.

I have the Cub Cadet version of this lawn mower. I bought it used. The blade was shot so I bought a new one. The mower developed a significant vibration with the new blade. After your video I noticed that my deck was on an angle so I fixed that, still the vibration persists. I checked the blade balance (with a nail) it seems spot on. Not sure where to go from here, the spindle does not seem to have any slack or lateral movement. Any suggestions on what it might be?

Can't figure out how to get the auto choke and throttle set correctly on this one. Starts at cold start then dies and won't start again. Strange and frustrating since it only has 146 hours on it

Thanks dude for the video.

I got a 2019 with 150 hours no problems and I can change my oil in under a minute

Great videos.

Sao các bạn không bán hàng về Việt Nam

I bought a 54 inch with fabricated 3 years ago almost 700 hours replaced a starter and throttle cable awesome machine also have 54 tractor fabricated deck gtx 2000 power steering 11 years old no problems still mows like a champ

Thank you for posting this it really helped.

Praise God for the conversion kit option!

Changed one of these today after viewing your tutorial. Thanks for the help!

Why is there only 1 remaining OEM tire on the rh front? I have same exact tractor,never have had to change out tires.

Hey buddy i like your videos, im in the market for a new rider and im really liking the x380 48 inch cut would that be a good choice

What is a slap hammer?? 😂 That's a new one. The rest of the world knows that as an impact driver. And who uses non shrink wrapped wire connectors on something that gets wet? I wished I hadn't watched this video.

Does this mower have a starter solenoid? I have the same mower, but can't find it.

This saved me!!!! Thanks!

Appreciate this video sir

So, Martin, the only reason the belt jumped off this one was that one keeper not being installed into that one cutout? Bummer, and probably an easy mistake to make. Too bad they didn’t extend that piece so it had an actual hole the keeper had to fit into. On the other hand this makes it easier to replace a belt, right?

It's unfortunate that they don't make the idler pulleys with replaceable bearings. I have drilled out the rivets and replace the bearings # 6203. Then use grade 5 nuts and bolts to put back together. Much cheaper, and if the bearings go bad again, about 5 minutes and it can be changed out. The pulley itself very seldom go bad, just the bearings

FYI...on grasshopper deck...mechanic told me to adjust tensioner spring out to fit a nickle between a coil......just fyi

what about a head gasket causing fuel issues bc it messes with vacuum sometimes

It's Cheaper Or Near The Same Amount Of Money To Buy New Spindles Then Buy New Bearings And Install Them Into The Old Spindle Housings I Always Add More Grease Directly Into The Bearings By Removing The Bearing Dust Cap They Never Have Enough Grease In The Bearings , Bare Minimum Amount. Even The Ones In The New Spindle Housing I Would Add More Grease. Those Zerx Fittings ( Grease Nipples ) Are A Waste Of Time And Grease , Because The Grease Can't Get Into The Bearings, Because Of The Dust Caps On The Bearings It Must Have Been A Long Day , You Messed Up A Bit With The Pulleys 😂😂 Also Those Rear Deck Hangers Should Have Had Big Washers On It, If I'm Not Wrong ?

I use antizee because everyone washes their deck and that one bolt that goes thru will freeze on nut and break it loose which is a problem to redo and a lot of time 😊

Had to rewatch it, missed some doing other things, lolol it’s life as a care giver for wife ❤

Ahhhhhh whats the diagram on the deck itself , is that the drive belt or the deck belt ????????

I built tires for 25 years. In doing so, we lubed the flanges with lard. Not sure if this could be used in the same way you are using it. Also, if you ever get into grease with graphite in it, clean your hands with lard. That grease with graphite in it is next to impossible to get off with soap and water. With lard, you are clean in seconds.

i don't feel bad now i also could not remember how the belt went on a d140 this one had no belt diagram. but i did get it right after a couple of trys

Honda no longer making power equipment

One should not think about a mower blade edge the same way you would think about a knife edge. Consider the force that the mower blade is spinning, This means you need a stronger edge as opposed to a finer, sharper edge. If you thin that edge out, it's just going to "round over" as soon as it starts wearing and you'll have a fatter, duller edge. I would refrain from dickering with the edge of a new blade, and don't over-sharpen it when you do put the grinder to it.

Did I understand that Honda is getting out of the mower business?

Those JD decks on that particular mower are a terrible design. Plus it should probably be at least a 50" deck for that size mower. Thanks for the video.

Wouldnt you be able to install grease zerks?

Good video.

Good information there thanks 🙏

What would be the cost of the repair it’s an old mower.

On my machine the handle broke on the right side near the bottom.

The blade washer are concave and should be used. Also the pivot pulley spacer should be the other way and no washer is used.

We all, make mistakes. You, could've edited it out. We, wouldnt have known the difference. Great channel!

Good video !!!!!!!!!!!!!

I started watching your channel recently. This was a great video. What I like most is your candid demeanor. Nothing seems to rattle you and you honestly admit when you get something wrong and don't try to edit it out. It shows your authenticity and makes the rest us feel better in knowing we aren't the only ones who quickly forget how something goes back together. Your experience shows itself because you eventually figure out what you did wrong and always correct it. Keep up the good work. Also i appreciate how you take time to be sure you get the best camera angle so we can see exactly what you are doing.

First rate job👍